一定牛彩票

Door leaf filling process for fire door factory

assignment order

Steps

Operating standards

Operation points and precautions

One

First Article Inspection

、检查门扇外观质量 1. Check the appearance quality of the door leaf

No craters, leaks, or scratches on the surface

Check the surface for no craters, leaks, scratches, etc.

、检查里板 2.Check the lining

No missing welding

With or without leaky hinges, door closer nuts

Operating standards

、搬扇 1 , moving fan

Door leaf on flat platform

、掀扇 2 , fan

Open the panel and lean on the door leaf in front of the turnover car to prevent pitting

、珍珠岩选用 3. Selection of perlite

Check the corresponding perlite thickness, choose different types of perlite materials for different products

、刮胶 4.Squeegee

齿豁无凝 Before scraping the glue, check whether the glue scraper is clean and the teeth are free from condensation.      

Blocking glue evenly

、 带玻璃刮胶 5 , with glass scraper

The inside of the glass panel is scraped inwardly and the panel is scraped inward.

If the glue is scraped away from the glass port, when the press presses the door leaf, the glue will be squeezed out of the glass port.

Pollution facade and glass.

、刮板 6.Scraper

130*0.8 Scraper specifications: width 200 * height 130 * thickness 0.8

填料 7.Filling

Choose the same slate as the door leaf

 

、珍珠岩对接 8.Perlite docking

Perlite is filled in the seam after the fight

、填料工艺 9 , filler technology

Refer to the attached packing process drawing

、锁具 10 、 Lock

The plug on the door leaf is used as the reference. The hole with the handle above the side lock hole is a pipe well lock.

、放插销 11 , put the bolt

Alignment of holes

According to the level of the door leaf, select the protective box of the same level, and the inside panel is aligned left and right.

、扣扇 12 , buckle fan

Inside panel hinge, hinge side angle, roller door closer door nut

、咬口 13 , bite

度角,里面板平齐,外观无损坏 90 degree angle, the inner panel is flush, and the appearance is not damaged

、整理 14 , finishing

Fill the fan at any time under pressure

、表面检查 15 , surface inspection

Packaging film is flat and rolled up rip off

、抬扇 16 , lifting fan

Hold one person up and down, hold the door leaf firmly with both hands, and force

、入扇 17 , into the fan

Cover seam plate side alignment

、受压 18.Pressure

Perlite pressure value 5mpa
小时。 Compression time: 6 hours.
Press lift operator must not leave

Note: Failure to reach the pressure value will cause the door leaf to empty, and below the pressure time will cause fireproof glue.

Without moving the door leaf back and forth, the inner panel collapsed and two skins inside and out.

three

Self-check

压力表是否到指定值 1. Whether the pressure gauge reaches the specified value

Every time the lower limit must be checked

The pressure value cannot be reported in time for repair, and the door leaf replacement press is pressed in time.

钢质防火门材料要求 Previous: Material requirements for steel fire doors
断桥铝防火窗生产厂制作工艺 Next: Manufacturing process of broken bridge aluminum fire window production plant
防火门十大品牌
Hebei Jiu'an Fire Door Manufacturing Group Co., Ltd. <br /> Sales Hotline: 0312-5971018 18932668178
Company Fax: 0312-5971010
Address of the head office: China Top Ten Brand Fire Doors, No. 531 Fengqi Street, Private Technology Industrial Park, Qiyi East Road, Baoding, Hebei, China [Technical Support: Giggle SEO Service Hotline: 18630277802]
var _hmt = _hmt || []; (function() { var hm = document.createElement("script"); hm.src = "https://hm.baidu.com/hm.js?be055eb5acfdc25d3bd72279b8418725"; var s = document.getElementsByTagName("script")[0]; s.parentNode.insertBefore(hm, s); })();