一定牛彩票

Fire door closers installation method requirements

Update 2015-12-28 11:31:24
In order to ensure that the documents are easy to read and save, the specifications of the fire door are downloaded in the form of Baidu network disks. The document extraction code is below this content.
Purpose: To confirm the installation preparation, method and commissioning of the door closer.

First, the installation method of the door closer without steel door without bracket (door closer housing on the frame)

1. Be sure to find a climbing tool (stool) when installing the door closer.
2. Before installing the door closer, assemble ten to twenty poles on the support bar, and distinguish several left fans and several right fans. The regulator of the door closer is on the right, (the opposite direction of the hinge) and the right fan is the opposite. After the support rods are separated, the large rods are perpendicular to the top of the door closer, and the small rods are closed.
3. Start to install the door closer. The screw holes on the frame have been opened. With the regulating valve against the hinge side, install the screw with the large rod facing downwards (face up). Do not tighten the four short screws. After all four screws are tightened, tighten each one half. The supplementary content is: the screw must be on to the end, the screw that can not be screwed to the end with a tap to ensure that the screw is fastened, the door closer rotates in the correct direction, and the installation team who fails to pass the penalty will be charged 5 yuan / piece.
4. After the main body is finished, the small rod is started, and the screw eyes on the fan have been opened. First put the small pole on the fan, the small pole is vertical (the door is closed), and screwed. Bend the large rod to the position of the small rod (the length of the small rod can be adjusted). Adjust the length of the small rod. After connecting it, put on the screws.
5. After opening, try opening and closing the door. The closing speed is 4-6 seconds, and the door is locked for 1 second. If it is not adjusting the regulating valve, turn clockwise to decrease the speed, otherwise increase the speed. Generally, the closing valve on the left door closer is the closing speed, and the right door is the opposite. The supplementary content is: 5 yuan for each failure.
6. For a single door, the left door is the same as the left fan, and the right door is the same as the right door.

Second, steel door reverse installation with bracket door closer installation method (big head on the fan)

1. Before assembling the door closer, assemble ten to twenty poles on the support bar, and distinguish between several left fans and several right fans. The door closer control valve for the left fan is on the right, and the opposite for the right fan. After the support rod is separated, the large rod should be parallel to the door closer on the upper surface of the regulating valve surface, and the small rod should be closed.
2. Start to install the door closer. The screw holes on the fan have been opened. With the regulating valve facing away from the hinge side, install the screw with the large rod facing upwards (face up). Do not tighten the four short screws. After all four screws are tightened, tighten each one half. Be sure to tighten the screws to the end. The supplementary content is: 5 yuan for each failure.
3. After the main body is finished, the small rod is started, and the screw holes on the frame have been opened. Attach the bracket of the small pole to the fan first, and then the small pole. Fit the screws. The small rod is parallel to the door frame and the large rod is bent to the position of the small rod (the length of the small rod can be adjusted). After adjusting the length of the small rod, screw it in. The supplementary content is: 5 yuan for each failure.
4. After opening, try opening and closing the door. The closing speed is 4-6 seconds, and the door is locked for 1 second. If it is not adjusting the regulating valve, turn clockwise to decrease the speed, otherwise increase the speed. The supplementary content is: 5 yuan for each failure.

Third, the company's wooden door anti-door closers can only be equipped with a bracket.

1. Be sure to find a climbing tool (stool) when installing the door closer.
2. Before installing the door closer, assemble ten to twenty poles on the support bar, and distinguish several left fans and several right fans. The door closer control valve for the left fan is on the right, and the opposite for the right fan. After the support rod is separated, the large rod should be parallel to the door closer on the upper surface of the regulating valve surface, and the small rod should be closed.
3. Start punching flat. The eye position of the bracket on the frame near the vertical frame is 52mm from the vertical frame edge and 12mm from the horizontal frame edge (near the fan frame edge). Then use the bracket to punch a hole with a diameter of 4mm, and screw it in. First put the small rod on the bracket, the small rod is parallel to the door (the door is closed), and screwed. Bend the large rod to the position of the small rod (the length of the small rod can be adjusted). Adjust the length of the small rod. After connecting it, screw in. The supplementary content is: 5 yuan for each failure.
4. After opening, try opening and closing the door. The closing speed is 4-6 seconds, and the door is locked for 1 second. If it is not a regulating valve, turn clockwise to decrease
Speed, and vice versa. Generally, the closing valve on the left door closer is the closing speed, and the right door is the opposite. The supplementary content is: 5 yuan for each failure.

Four, steel door is installed door closer installation method

1. Be sure to find a climbing tool (stool) when installing the door closer.
2. Before installing the door closer, assemble ten to twenty poles on the support bar, and distinguish several left fans and several right fans.
3. The door closer control valve of the left fan is on the left, and the right fan is the opposite.
4. After the support rods are separated, the large rods should be perpendicular to the door closer, and the small rods should be closed.
5. Start to install the door closer body. The screw eyes on the fan have been opened. Do not tighten the four short screws. After all four screws are tightened, tighten the screws one by one. Be sure to tighten the screws to the end. The supplementary content is: 5 yuan for each failure.
6. After the main body is finished, the small rod is started, and the screw holes on the frame have been opened. First put the small rod on the frame, the small rod is vertical frame,
Fit the screws. Bend the large rod to the position of the small rod (the length of the small rod can be adjusted). Adjust the length of the small rod.
Screws. The supplementary content is: 5 yuan for each failure.
7. After opening the door, try opening and closing the door. The closing speed is 4-6 seconds, and the door is locked for 1 second. If it is not a regulating valve, turn clockwise to decrease
Speed, and vice versa. Generally, the closing valve on the left door closer is the closing speed, and the right door is the opposite. The supplementary content is: 5 yuan for each failure.
8. For single door opening, left door opening is the same as left fan installation, and right door opening is the same as right door installation.

Five, wooden door is installed door closer method

1. The difference between the installation of wooden door and steel door is that the wooden door does not open well. The first 1, 2 are the same as the steel door.
2. The eye position on the upper left corner of the left fan is 11-12 cm from the fan hinge and 2.5 cm from the fan. The position of the upper right corner eye on the right fan is 11-12 cm from the fan hinge edge and 2.5 cm from the fan upper edge. Mark the first eye and mark it. After putting the door closer in place, punch the first screw with a power drill before ordering the other screws. Screws should be drilled directly with a rechargeable hand drill. The supplementary content is: 5 yuan for each failure.
3. The eyes on the frame are directly above the two eyes on the door closer away from the hinge side, one eye 2.5 cm below the frame. The other eye is compared with a small rod, which is generally away from the door closer, and the screw should be directly drilled with a rechargeable hand drill. Everything else is the same as the steel door.
Related recommendation: Fire door linkage door closer installation requirements

Download link

After clicking the download link, please enter the document extraction code: 9qyb

钢质防火门技术标准 Previous post: Technical standards for steel fire doors
防火门五金规范 Next: Fire door hardware specifications
防火门十大品牌
Hebei Jiu'an Fire Door Manufacturing Group Co., Ltd. <br /> Sales Hotline: 0312-5971018 18932668178
Company Fax: 0312-5971010
Address of the head office: China Top Ten Brand Fire Doors, No. 531 Fengqi Street, Private Technology Industrial Park, Qiyi East Road, Baoding, Hebei, China [Technical Support: Giggle SEO Service Hotline: 18630277802]
var _hmt = _hmt || []; (function() { var hm = document.createElement("script"); hm.src = "https://hm.baidu.com/hm.js?be055eb5acfdc25d3bd72279b8418725"; var s = document.getElementsByTagName("script")[0]; s.parentNode.insertBefore(hm, s); })();